TILLAGE WEAR PARTS MADE EASY!

Chisel Plow

CHISEL SPIKES

Nichols double-end chisel points are our classic chisels. The #28 has been a favorite for years. Constructed of heat-treated steel, these chisels are made to last.

7/16" Holes2-1/4" hole spacing
Size Material Ends Style Part Number Weight (lbs)
2" x 12-1/2" 1/2" diamond S1215* 4.3
2" x 15-1/2" 5/8" diamond 1759D 6.5
2" x 16" 1/2" swedged HC2 4.4
2" x 16" 5/8" diamond HC2C8-7 5.5
3" x 15" 3/8" swedged 3H 4.4
* S1215 holes are slotted to accomodate 2-1/2" centers
1/2" Holes 2-1/4" hole spacing
Size Material Ends Style Part Number Weight (lbs)
2" x 16" 5/8" diamond HC2C8 5.5
2" x 16" 5/8" swedged #28 5.3
2" x 16" 5/8" diamond HC2C8SP 5.5
2" x 16" 3/4" diamond H342D 6.7
4" x 15" 3/8" diamond HC4-2 5.3
4" x 16" 1/4" flared RA4 4.2
4" x 16" 1/4" flared RA4S* 4.2
4" x 16" 5/16" flared RA5 5.7
4" x 16" 5/16" flared RA5S* 5.7
* RA4S and RA5S holes are slotted to accomodate 2-1/2" centers
Heavy Forged Chisels
Size Material Ends Style Part Number Weight (lbs)
2-1/8" x 18" 1" forged H22-2 8
2-1/4" x 18" 1-1/4" forged H23-2 13

Chisels for the Nichols heel sweep are available in two sizes. Due to the combination of chiseling and sweeping causing greater draft, more power is required. To combat this, the narrow chisel is a sure bet.

Chisels for Heel Sweeps
Size Part Number Weight (lbs)
Regular H342CP 5.2
Narrow H13CP 6
Be sure to follow the instructions for proper mounting of the Nichols heel sweep

TWISTED CHISELS

Nichols twisted chisels have a slight helical twist but retain a direct point on the center of the piece. Also available hardfaced, they are offered in two material thicknesses.

Centerpoint 1/2" Holes 2-1/4" hole spacing
Size Style Part Number Weight (lbs)
3" x 22" right 383R-2 6.2
3" x 22" left 383L-2 6.2
3" x 22" hardfaced right 383R-2HF 6.6
3" x 22" hardfaced left 383L-2HF 6.6
1/2" holes for 2-1/4" centers 3/8" Material      
       
Centerpoint 1/2" Holes 2-1/4" hole spacing
Size Style Part Number Weight (lbs)
3" x 22" right 483R-2 8.1
3" x 22" left 483L-2 8.1
3" x 22" hardfaced right 483R-2HF 8.5
3" x 22" hardfaced left 483L-2HF 8.5
4" x 22" right 583R-2 10.4
4" x 22" left 583L-2 10.4
4" x 22" hardfaced right 583R-2HF 10.8
4" x 22" hardfaced left 583L-2HF 10.8
1/2" holes for 2-1/4" centers 1/2" Material

Nichols slash points are based on our double-end chisels only with diagonally cut ends and are available hardfaced.

HARD-FACING CAN DOUBLE THE SERVICE LIFE!

Slashpoint 1/2" Holes 2-1/4" hole spacing
Size Style Part Number Weight (lbs)
3" x 22" right SL123R 9.6
3" x 22" left SL123L 9.6
3" x 22" hardfaced right SL123RHF 10
3" x 22" hardfaced left SL123LHF 10
4" x 22" right SL124R 12.6
4" x 22" left SL124L 12.6
4" x 22" hardfaced right SL124RHF 13
4" x 22" hardfaced left SL124LHF 13

CONVENTIONAL SWEEPS

Nichols conventional chisel plow sweeps have been designed with a large web and long nose for extra strength and lasting penetration. Each sweep is constructed of high-quality hardened steel which results in significantly better wear resistance. Available in four different stem angles and two material thicknesses.

43° Conventional Chisel Plow Sweeps43° Stem Angle, 2" wide shank, 2-1/4" hole spacing for 1/2" plow bolts
1/4" Material
Size Part Number Weight (lbs)
10" JH10-2 4.25
12" JH12-2 4.8
14" JH14-2 5.3
16" JH16-2 6
18" JH18-2 7
Will fit these machines: Ingham, some MF, Massey-Harris, Mel-Cam Cultiweeder, Minn-Toba 3pt hitch, Morris 200, '82 Magnum, Oliver 500, 3500, Wilrich (earlier models)
45° Conventional Chisel Plow Sweeps45° Stem Angle, 2" wide shank, 2-1/2" hole spacing for 1/2" plow bolts
1/4" Material
Size Part Number Weight (lbs)
10" IH10 4.25
12" IH12 4.8
14" IH14 5.3
16" IH16 6
18" IH18 7
5/16" Material
Size Part Number Weight (lbs)
10" IH10-F 5.1
12" IH12-F 6
14" IH14-F 6.6
16" IH16-F 7.5
18" IH18-F 8.8
Will fit these machines: CCIL, CO-OP, IH, IH Case
47° Conventional Chisel Plow Sweeps47° Stem Angle, 2" wide shank, 2-1/4" hole spacing for 1/2" plow bolts
1/4" Material
Size Part Number Weight (lbs)
10" 4710-2 4.25
12" 4712-2 4.8
14" 4714-2 5.3
16" 4716-2 6
18" 4718-2 7
Will fit these machines: Krause (early low-clearance), Melroe-Clark
50° Conventional Chisel Plow Sweeps50° Stem Angle, 2" wide shank, 2-1/4" hole spacing for 1/2" plow bolts
1/4" Material
Size Crown Part Number Weight (lbs)
6" High HC6B-2 3.4
8" High HC8B-2 3.8
10" High HC10B-2 4.25
12" High HC12B-2 4.8
14" High HC14B-2 5.3
16" Flat HC16AA-2 6
16" Medium HC16A-2 6
16" High HC16B-2 6
18" Flat HC18AA-2 7
18" Medium HC18A-2 7
18" High HC18B-2 7
20" Flat HC20AA-2 7.56
20" Medium HC20A-2 7.56
22" Medium HC22A-2 7.7
24" Meduim HC24A-2 9.2
5/16" Material
Size Crown Part Number Weight (lbs)
6" High HC6BF-2 4
8" High HC8BF-2 4.3
10" High HC10BF-2 5.1
12" High HC12BF-2 6
14" High HC14BF-2 6.6
16" Medium HC16AF-2 7.5
16" High HC16BF-2 7.5
18" Medium HC18AF-2 8.8
18" High HC18BF-2 8.8
26" Medium HC26F-2 15.25
Will fit these machines: Bourgault (deep tillage), Case (later), Deere, Degelman, Fallow King, Fallow-Master, Flexi-Coil, Friggstad, Kewanee, Krause (low-clearance), Landol, Lely, Mel-Cam, MF 128, Minn-Toba 120, 176, Morris Magnum, Noble XR20, Oliver 247, 248, 347, Renn, Robin Nodwell, Roll-O-Flex, Sunflower, Versatile, Victory, White.

NOK-ON CONVENTIONAL SWEEPS

HIGH CROWN
1/4" Material
Size Part Number Weight (lbs)
10" HQC10B 5.4
12" HQC12B 5.5
14" HQC14B 6.3
16" HQC16B 6.6
18" HQC18B 7.4
5/16" Material
Size Part Number Weight (lbs)
16" HQC16BF 7.2
18" HQC18BF 7.8
LOW CROWN
1/4" Material
Size Part Number Weight (lbs)
16" HQC16AA 7.2
18" HQC18AA 8.2

ULTRAWING SWEEPS

The Ultrawing sweep, exclusively from Nichols, is the highest-quality, longest-lasting, and best-performing sweep on the market. With a longer nose, curved convex wings, and an optimal crown configuration, the sweep anticipates wear. The unique, patented Ultrawing design maintains the sweep’s shape over time, resulting in a significantly longer life of the piece.

The nose of the Ultrawing is elongated for better penetration, and to also ensure the tip stays sharp for as long as the sweep is used.  The Ultrawing’s optimal crown configuration is an important factor in the sweep’s design that assists in maintaining the original shape of the piece’s entire edge throughout the life of the sweep. The curved wings of the Ultrawing sweep converge at the crown at an optimum angle, elevating the crown for the most efficient wear. Acting like an old scythe, the curvature of the wings provide extra weed killing ability by preventing the weeds from sliding off the ends of the sweep, which is often the case with a standard conventional sweep, leaving partially severed roots. In addition to the wings being curved, they also have a convex surface, which turns the sweep’s leading edge downward to provide an increased angle of presentation to the soil. The convex surface also results in a stiffening effect to the wings, in addition to passing soil smoothly over the convex surface without excessively lifting the soil. For even more strength, the neck of the Ultrawing of the sweep where the stem and wings intersect. This crimped area also helps separate the soil away from the bolt heads. All of these features combined are what sets the Ultrawing sweep apart from any other sweep with excellence in performance, durability, and quality.

1/4" Material - Large Pattern
Size Crown Part Number Weight (lbs)
20" High B5020-2 7.7
22" High B5022-2 8.4
24" High B5024-2 9
5/16" Material
Size Crown Part Number Weight (lbs)
8" High B5008F-2 5.2
12" Flat AA5012F-2 6
12" High B5012F-2 6
14" Flat AA5014F-2 6.6
14" High B5014F-2 6.6
16" Flat AA5016F-2 7.5
16" High B5016F-2 7.5
18" High B5018F-2 8.25
5/16" Material - Large Pattern
Size Crown Part Number Weight (lbs)
26" High B5026F-2 15.5
Will fit these machines: Bourgault (deep tillage), Case (later), Deere, Degelman, Fallow King, Fallow-Master, Flexi-Coil, Friggstad, Kewanee, Krause (low-clearance), Landol, Lely, Mel-Cam, MF 128, Minn-Toba 120, 176, Morris Magnum, Noble XR20, Oliver 247, 248, 347, Renn, Robin Nodwell, Roll-O-Flex, Sunflower, Versatile, Victory, White

NOK-ON ULTRAWING SWEEPS

High Crown
1/4" Material
Size Part Number Weight (lbs)
10" BQC10B 5.3
12" BQC12B 5.8
14" BQC14B 6.4
16" BQC16B 7
18" BQC18B 7.4
5/16" Material
Size Part Number Weight (lbs)
12" BQC12F 7.2
14" BQC14F 7.8
16" BQC16F 8.4
18" BQC18F 9
Low Crown
1/4" Material
Size Part Number Weight (lbs)
12" AAQC12B 5.8
14" AAQC14B 6.4
16" AAQC16B 7
18" AAQC18B 7.5
5/16" Material
Size Part Number Weight (lbs)
12" AAQC12F 7.2
14" AAQC14F 7.8
16" AAQC16F 8.4
18" AAQC18F 9

KLIPPED WING SWEEPS

Nichols Klipped Wing chisel plow sweeps are based on the same standards as the conventional chisel plow sweeps, but the wings are trimmed parallel to the direction the sweep is run, keeping the width consistent throughout the life of the sweep.

43° Klipped Wing Chisel Plow Sweeps43° Stem Angle, 2" wide shank, 2-1/4" hole spacing for 1/2" plow bolts
1/4" Material
Size Part Number Weight (lbs)
16" JH16K-2 4.25
18" JH18K-2 4.8
Will fit these machines: Ingham, some MF, Massey-Harris, Mel-Cam Cultiweeder, Minn-Toba 3pt hitch, Morris 200, '82 Magnum, Oliver 500, 3500, Wilrich (earlier models)
45° Klipped Wing Chisel Plow Sweeps45° Stem Angle, 2" wide shank, 2-1/2" hole spacing for 1/2" plow bolts
1/4" Material
Size Part Number Weight (lbs)
10" IH10K 6
12" IH12K 6.75
14" IH14K 7.25
16" IH16K 7.35
18" IH18K 8.25
Will fit these machines: CCIL, CO-OP, IH, IH Case
47° Klipped Wing Chisel Plow Sweeps47° Stem Angle, 2" wide shank, 2-1/4" hole spacing for 1/2" plow bolts
1/4" Material
Size Part Number Weight (lbs)
10" 4710K-2 6
12" 4712K-2 6.75
14" 4714K-2 7.25
16" 4716K-2 7.35
18 4718K-2 8.25
Will fit these machines: Krause (early low-clearance), Melroe-Clark
50° Klipped Wing Chisel Plow Sweeps50° Stem Angle, 2" wide shank, 2-1/4" hole spacing for 1/2" plow bolts
1/4" Material
Size Crown Part Number Weight (lbs)
10" High HC10BK-2 6
12" High HC12BK-2 6.75
14" High HC14BK-2 7.25
16" Flat HC16AAK-2 7.35
16" Medium HC16AK-2 7.35
16" High HC16BK-2 7.35
18" Medium HC18AK-2 8.25
18" High HC18BK-2 8.25
5/16" Material
Size Crown Part Number Weight (lbs)
10" High HC10BFK-2 7.25
12" High HC12BFK-2 8.5
14" High HC14BFK-2 9.5
16" High HC16BFK-2 9.75
18" High HC18BFK-2 10.5
Will fit these machines: Bourgault (deep tillage), Case (later), Deere, Degelman, Fallow King, Fallow-Master, Flexi-Coil, Friggstad, Kewanee, Krause (low-clearance), Landol, Lely, Mel-Cam, MF 128, Minn-Toba 120, 176, Morris Magnum, Noble XR20, Oliver 247, 248, 347, Renn, Robin Nodwell, Roll-O-Flex, Sunflower, Versatile, Victory, White

NOK-ON KLIPPED WING SWEEPS

High Crown
1/4" Material
Size Part Number Weight (lbs)
6" HQC6BK 3.5
8" HQC8BK 4
10" HQC10BK 6.2
12" HQC12BK 6.6
14" HQC14BK 7
16" HQC16BK 7.2
18" HQC18BK 8.2
5/16" Material
Size Part Number Weight (lbs)
6" HQC6BKF 4
8" HQC8BKF 4.3
14" HQC14BKF 7.4
16" HQC16BKF 8
18" HQC18BKF 8.6
Low Crown
1/4" Material
Size Part Number Weight (lbs)
16" HQC16AAK 7.2
18" HQC18AAK 8.2

HEEL SWEEPS

The Nichols heel sweep is a revolutionary design that allows both sweeping and chiseling to be done simultaneously. This combination results in breaking up the hardpan to encourage better root penetration and absorbtion of moisture.

Size Part Number Weight (lbs)
16" HS16B 6.5
18" HS18B 7.5
Hardfaced Top
Size Part Number Weight (lbs)
16" HS16HFT 7
18" HS18HFT 8
Hardfaced Bottom
Size Part Number Weight (lbs)
16" HS16HFB 7
18" HS18HFB 8
Be sure to follow the instructions for proper mounting of the Nichols heel sweep
Sitemap   |   Privacy Statement   |   Copyright 2013 RangeLine Group, LLC.   All rights reserved.   Site developed by: LaJuett Web site design Rochester, NY.